Hook up speakers to receiver

I thought that I should plug that into one of the normal input jacks, such as CD instead of the phono input as I was afraid that the amplified signal may be too high and damage the phono input. I now think that this was possibly a mistake since there is a noticeable noise before and after the music on the disc plays. Thanking you in advance of your reply and if by any chance you are unable to help me please keep on doing the great work you are for others. Thanks for the good guide, but I have trouble connecting the bare wire from my speaker to my Kenwood stereo receiver KR In order to connect the speaker wire to your Kenwood KR stereo receiver, you may need to buy spade connectors.


  • onion online dating.
  • single black parents dating sites?
  • dating peace corps.

You put the open side of the spade connector on the end of each wire and then attach the flat side of the spade connector to the screw terminals on your receiver. The reason I got it was to hook up a few speakers I inherited in our new house, already set up in the back corners of the room, with our TV. I also hooked up a radio antenna, and it works great: The issue I ran into is with output.

What do you need to set up a stereo system?

It may be that I will need to either 1 a new receiver, or 2 a new subwoofer. But the receiver clearly works fine, and the subwoofer is brand new. I would prefer some other solution. I tried googling and amazon-searching for various cable converters, analog to digital, digital to analog, etc. I think you can set this up so you can use both your receiver and your subwoofer.

How to Connect Audio Speakers to a Receiver

It is not an ideal setup, but if you need it to work without getting a new receiver or subwoofer it might be the only way. I would try connecting a cable from either the Tape or VCR record outputs into the back of your subwoofer. I have recently set them up again, however I only get sound out of one speaker. Both speakers work, I have the A channel selected, the speaker cables both work.

The balance is in the centre, I have tried different input cables and even different inputs to the amplifier I have been using the CD input as default. When I have no inputs inserted if I turn up the master volume to full I get the usually hissing from both speakers nothing crackly. The receiver only gets sound from one of the two channels either the left or the right instead of getting both channels like it normally would.

Since you hear the hissing noise when you turn up the volume, your receiver can output sound to both speakers.

Video of the Day

But if it can only get one of two channels from the RCA inputs, it will only output that one channel. To get it fixed, it might be as simple as re-soldering a connection between the inputs and the amp or it could be something more complicated and expensive. If you want to get it fixed, I would recommend contacting United Radio since they specialize in repairing Sony equipment. You will have to ship it to them and then they give you an estimate for repair if it can be repaired.

In total, it could be almost as costly as buying a brand new Sony receiver with a warranty. You might be able to find someone who does repair local to you, but with equipment like surround receivers, parts might be expensive or impossible to get. Hi Nick, first off your setup instructions are great! We are looking to build a new stereo system. Will Sonos wireless speakers Work with this setup with home wifi or can you recommend one that will? Thank you in advance! The Yamaha R-S receiver works best with traditional wired speakers.

Connecting powered bookshelf speakers to Stereo receiver [Solved] - Speakers - Audio

The only way I can think of to hook up Sonos wireless speakers like the Play 5, 3, 1, or PlayBar to your stereo is a bit complicated:. I recommend sticking with regular wired speakers for your stereo system and if you want a second system for wireless speakers, go for the Sonos. The Sonos wireless speakers are great for playing music from the internet, but mixing in traditional sources like a CD player or turntable complicates how you have to set your system up and use it.

If there were any good wireless speakers you could directly hook up to a stereo receiver, I would recommend them. I am trying to hook up my sony t. On the back of your TV, look for an audio output. You will either find a red and white analog audio output, an optical audio output, or both. Next, find an input on the back of your Onkyo receiver.

If your receiver has an optical audio input, use that because it will give you the full, digital sound straight from the TV. You will need an optical cable to do this. If not, use the regular red and white analog audio input for your TV. You will need an analog audio cable to do this.

Finally, set your receiver to whatever input you used for your TV. Some receivers have a TV input, so use that if you can. Nick, Thanks for your concise and intelligent guide.

If you have any suggestions to add to this guide, feel free to let me know. I do not have a system of any kind outside of a Bluetooth speaker that I use for streaming from my phone. I am going to purchase a record turntable looking at the Audio-technica at-lp60 turntable. I was told that I should buy an older receiver with phono on it and have found some older kenwood and pioneer receivers at a local pawnshop that are reasonable.

My question is that I want to listen to the turntable in different rooms then it is in and would prefer to buy a wireless speaker system. Can you connect wireless speakers to an older receiver like that or is the technology not compatible? Any other way I could accomplish it? To answer your question, yes it is possible to connect speakers wirelessly. You can do this with a wireless receiver and transmitter kit like the Soundcast SurroundCast. The advantage of this setup is you can use your turntable with your stereo receiver and listen with any pair of speakers wirelessly.

However, this type of setup will compromise the sound quality and the volume level you can listen at for the convenience of wireless speakers. If you turn the volume level up too high, it could blow the speakers or the wireless receiver. I have an old technics model sa-gx stereo receiver and I used it about a week ago everything was working great, but I recently moved it and tried playing the radio.

The volume on high but it sounded so low. How do I get it where the volume can return to normal install of low?

It sounds like one or a few things might be a problem:. I always try swapping out as many parts of the system as possible to see what may be wrong. The easiest thing to try is swap out the speaker wires. Speaker wires can be damaged even if they look fine and this may cause problems with the receiver. Next, try different sources of music like a CD player or iPod. Try your speakers on another stereo receiver.

If they sound the same on a different receiver as yours, then the problem may be the speakers. If the speakers sound noticeably better, the problem may be the receiver. Try taking it back to the store you bought it an see if they can test the receiver on one of their stereo setups. Also, try calling Technics and see if they have any authorized repair centers near you. And is it the wires or stereo? To figure out where this problem might be, test each individual piece of equipment first the stereo receiver, then the speakers, then the speaker wires, and so on on a second stereo system that you know works.

So try playing your stereo receiver on a different set of speakers and wires, then try playing your speakers on a different stereo receiver, etc.

How to Connect a Stereo System

This will narrow down your search to find which piece of equipment is causing the problem. It might be something as simple as replacing the speaker wires. Just like cars, electronics wear out from time and use. Like Ann, I would like to use wireless speakers with my vintage system. Is this possible, can you suggest adapters to do this, as well as wireless speakers that would be appropriate. I do not want to spend a lot of money on this. To play wireless music from your vintage system to speakers, I would recommend the Soundcast Surroundcast: This will let you hook up any small sized speakers to it so you can play music from your sound system to wherever you want your speakers to be.